Makes front sight staking effortless, faster and far more accurate. Improved, offset punch design efficiently directs the full force of the hammer blow downward against the sight tenon. Hardened, "V"-shaped tip easily displaces both wide and narrow tenons for a great-looking, tight-fitting front sight that won't shoot loose. Large, square shaft is easier to hold, see and hit so there's less chance of a missed hammer blow striking your customer's expensive slide.
SPECS: Steel, blued. 5/16" (7.9mm) x ½" (12.7mm) x 4½" (11.4cm) long shaft. Replaceable, hardened steel tip. Fits 1911 Auto. Includes complete instructions.
Mehr...
Vereinfacht das Abstecken von Visieren
Müheloses, schnelles und weitaus genaueres Abstecken des Visiers. Das verbesserte, versetzte Stempeldesign lenkt die volle Kraft des Hammerschlags effizient nach unten gegen den Visierzapfen. Die gehärtete, V-förmige Spitze verschiebt leicht breite und schmale Zapfen und sorgt so für ein gut aussehendes, eng anliegendes Visier, das sich nicht löst. Der große Vierkantschaft ist leichter zu halten, zu sehen und zu schlagen, sodass die Wahrscheinlichkeit geringer ist, dass ein verpasster Hammerschlag auf die teure Rutsche Ihres Kunden trifft.
Angaben: Stahl, gebläutet. 5/16 "(7,9 mm) x (12,7 mm) x 4" (11,4 cm) langer Schaft. Austauschbare Spitze aus gehärtetem Stahl. Für 1911 Auto. Enthält vollständige Anweisungen.
Mehr...
Kundenbewertungen zu BROWNELLS SWAGE POINT
Anzahl der Bewertungen: 12
Von brownells.com: 12
Durchschnittliche Bewertung: 4,8
A necessary 1911 tool(12.03.2010)
If the directions are followed this is the best sight tool I have used for both narrow & wide tenon sights. I have also used it to stipple the dovetail of rear sights for a secure fit.
Valuable tool(27.05.2010)
Excellent product, does a very good job staking 1911 front sight tenons. Strong and easy to use and you can rotate the point to vary your impression.
Only problem I had was the set screw which hold in the point kept loosening and the tip falling out after a few hammer strikes. However I can work with that to have the ability to rotate the point. I ordered an addiitional tip in case I lost the one that came with it, which I did.
awesome(29.12.2011)
great product, works like a charm.
specific tool for a specific job(24.11.2012)
This tool worked flawlessly for stakeing the front sight on my Colt 1911M1A.
makes the job very easy(10.01.2013)
Although I think the price was a little steep for this tool, it is the right tool for the job if you are staking a front sight into the slide of a 1911.
The only problem I had with the tool was that the allen set screw would not hold the tip tight and I had to be careful not to loose it while staking a sight. 4 stars only because of the loose tip.
Do it right ONCE!!!(27.03.2013)
"Use the right tool for the job at hand!!"
As a 1911 Specialist, this tool combined with (080-000-454), produced excellent results for both of the 1911 front sighs I installed for clients. The installation went smoothly. The second sight installation turned out better than the first one.
The staking nipple did come out once or twice, but over all that is/was a minor setback of the tool!!
Recardo A. Bristow, VA
Works As Discribed!!!(04.10.2014)
Using the staking tool was easier than what I thought. A drill press vise would have helped, since you need something solid and firm under the front sight. It also frees up both hands. Start at the back of the tenon, work your way to the front.Turn the tip 90 degrees and work back to front again. Work the tenon until it is properly flared. Use a Dremel to grind the tenon down just enough for proper bushing installation. This was my first time at staking a front sight. Watched YouTube first. Great results.
Works Great - Tips for Use.(04.01.2016)
Works nicely. I use Black Max adhesive under under the sight. Clamp as pictured to hold everything steady. Then use little taps to slowly swage the tennon. -So easy with the correct tool.
This is the tool to replace the old style 1911 pressed in sights. Using this tool retains the value of those collector guns from the World Wars.
Steak no Stake(21.10.2019)
I got my Staking tool and went right to work installing the front sight on my Rock Island 1911, actually works pretty darn easy just keep an eye on what your doing.
I thought why didn't I think of this my self.
1911 Tenon Squoosher.(06.11.2019)
This is the tool to have to peen the front sight tenon for 1911 pistols. You cannot do it correctly from an angle, without high risk of slide damage. With good light, and a little care, this tool does a perfect job.
Great tool!(12.02.2020)
Used this tool when I replaced the sight on my WW1 1911. This is the only tool for the job. It also helps to have a bench block specific to the 1911 as it has a place for just such a job. YouTube has great videos on doing this job.
Artikel-Nr.: 080870213 BROWNELLS SWAGE POINT Müheloses, schnelles und weitaus genaueres Abstecken des Visiers. Das verbesserte, versetzte Stempeldesign lenkt die volle Kraft des Hammerschlags effizient nach unten gegen den Visierzapfen. Die gehärtete, V-förmige Spitze verschiebt leicht breite und schmale Zapfen und sorgt so für ein gut aussehendes, eng anliegendes Visier, das sich nicht löst. Der große Vierkantschaft ist leichter zu halten, zu sehen und zu schlagen, sodass die Wahrscheinlichkeit geringer ist, dass ein verpasster Hammerschlag auf die teure Rutsche Ihres Kunden trifft.
31.9EUR3231,90 €
*
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Makes front sight staking effortless, faster and far more accurate. Improved, offset punch design efficiently directs the full force of the hammer blow downward against the sight tenon. Hardened, "V"-shaped tip easily displaces both wide and narrow tenons for a great-looking, tight-fitting front sight that won't shoot loose. Large, square shaft is easier to hold, see and hit so there's less chance of a missed hammer blow striking your customer's expensive slide.
SPECS: Steel, blued. 5/16" (7.9mm) x ½" (12.7mm) x 4½" (11.4cm) long shaft. Replaceable, hardened steel tip. Fits 1911 Auto. Includes complete instructions.
Mehr...
Vereinfacht das Abstecken von Visieren
Müheloses, schnelles und weitaus genaueres Abstecken des Visiers. Das verbesserte, versetzte Stempeldesign lenkt die volle Kraft des Hammerschlags effizient nach unten gegen den Visierzapfen. Die gehärtete, V-förmige Spitze verschiebt leicht breite und schmale Zapfen und sorgt so für ein gut aussehendes, eng anliegendes Visier, das sich nicht löst. Der große Vierkantschaft ist leichter zu halten, zu sehen und zu schlagen, sodass die Wahrscheinlichkeit geringer ist, dass ein verpasster Hammerschlag auf die teure Rutsche Ihres Kunden trifft.
Angaben: Stahl, gebläutet. 5/16 "(7,9 mm) x (12,7 mm) x 4" (11,4 cm) langer Schaft. Austauschbare Spitze aus gehärtetem Stahl. Für 1911 Auto. Enthält vollständige Anweisungen.
Mehr...
Kundenbewertungen zu BROWNELLS SWAGE POINT
Anzahl der Bewertungen: 12
Von brownells.com: 12
Durchschnittliche Bewertung: 4,8
A necessary 1911 tool(12.03.2010)
If the directions are followed this is the best sight tool I have used for both narrow & wide tenon sights. I have also used it to stipple the dovetail of rear sights for a secure fit.
Valuable tool(27.05.2010)
Excellent product, does a very good job staking 1911 front sight tenons. Strong and easy to use and you can rotate the point to vary your impression.
Only problem I had was the set screw which hold in the point kept loosening and the tip falling out after a few hammer strikes. However I can work with that to have the ability to rotate the point. I ordered an addiitional tip in case I lost the one that came with it, which I did.
awesome(29.12.2011)
great product, works like a charm.
specific tool for a specific job(24.11.2012)
This tool worked flawlessly for stakeing the front sight on my Colt 1911M1A.
makes the job very easy(10.01.2013)
Although I think the price was a little steep for this tool, it is the right tool for the job if you are staking a front sight into the slide of a 1911.
The only problem I had with the tool was that the allen set screw would not hold the tip tight and I had to be careful not to loose it while staking a sight. 4 stars only because of the loose tip.
Do it right ONCE!!!(27.03.2013)
"Use the right tool for the job at hand!!"
As a 1911 Specialist, this tool combined with (080-000-454), produced excellent results for both of the 1911 front sighs I installed for clients. The installation went smoothly. The second sight installation turned out better than the first one.
The staking nipple did come out once or twice, but over all that is/was a minor setback of the tool!!
Recardo A. Bristow, VA
Works As Discribed!!!(04.10.2014)
Using the staking tool was easier than what I thought. A drill press vise would have helped, since you need something solid and firm under the front sight. It also frees up both hands. Start at the back of the tenon, work your way to the front.Turn the tip 90 degrees and work back to front again. Work the tenon until it is properly flared. Use a Dremel to grind the tenon down just enough for proper bushing installation. This was my first time at staking a front sight. Watched YouTube first. Great results.
Works Great - Tips for Use.(04.01.2016)
Works nicely. I use Black Max adhesive under under the sight. Clamp as pictured to hold everything steady. Then use little taps to slowly swage the tennon. -So easy with the correct tool.
This is the tool to replace the old style 1911 pressed in sights. Using this tool retains the value of those collector guns from the World Wars.
Steak no Stake(21.10.2019)
I got my Staking tool and went right to work installing the front sight on my Rock Island 1911, actually works pretty darn easy just keep an eye on what your doing.
I thought why didn't I think of this my self.
1911 Tenon Squoosher.(06.11.2019)
This is the tool to have to peen the front sight tenon for 1911 pistols. You cannot do it correctly from an angle, without high risk of slide damage. With good light, and a little care, this tool does a perfect job.
Great tool!(12.02.2020)
Used this tool when I replaced the sight on my WW1 1911. This is the only tool for the job. It also helps to have a bench block specific to the 1911 as it has a place for just such a job. YouTube has great videos on doing this job.