Ihr Warenkorb ist leer.

Warenkorb

BROWNELLS
AR-15 PIVOT PIN DETENT INSTALLATION TOOL

050806104594 080216011

Makes installation of the M16 pivot pin and its detent faster and easier. Prevents loss of detents. Guides detent and spring into place and serves as a slave pin when installing the pivot pin.

SPECS: Blued steel. ¼" (6.3mm) diameter. 2½" (6.3cm) and 1½" (3.8cm) long legs .

Mehr...

Erleichtert die Installation des M16-Drehzapfens und seiner Arretierung. Verhindert den Verlust von Arretierungen. Führungen rasten ein und federn ein und dienen als Slave-Stift beim Einbau des Drehzapfens.

TECHNISCHE DATEN: Gebläuter Stahl. "(6,3 mm) Durchmesser. 2" (6,3 cm) und 1 "(3,8 cm) lange Beine.

Mehr...

Kundenbewertungen zu BROWNELLS PIVOT PIN INSTALLATION TOOL

Anzahl der Bewertungen: 17
Von brownells.com: 17
Durchschnittliche Bewertung: 5

Another Must Have (05.11.2009)

Did you know that a pivot pin spring and detent can actually attain Mach 1? Find it necessary to maintain an inventory of these pesky springs and detents because your's keep getting launched into outerspace? Prevent this from happening with this nifty tool. A must-have for your bench

You should definately have one. (17.02.2010)

[@] recommended this simple tool as one of the few tools needed to put a rifle together. It makes the installation of the tiny and slippery pivot pin a snap. If you try to do it by hand without the tool you are going to spend a lot of time struggling and cursing and dropping pieces! I highly recommend it.

A must have (30.12.2010)

I put together my first lower with a parts kit and the very helpul AR-15 videos on Brownells site. I was lucky to have access to this wonderful tool. It made installing the front pivot pin a snap!

Very, very, VERY handy tool! (12.03.2011)

Definitely worth the price of admission if you're building multiple lowers. Take note that if you're only planning to build one lower for yourself, it might be worth the $10 savings to not buy this tool as the pivot pin can be installed without it... but it'll take you three times as long with an equal amount of frustration. One safety tip when installing these detents and springs: wear glasses. They fly hard, and you'll be staring at them when they fly! Also, I cover my head and lower with an old bed blanket to contain the springs and detents when they fly-- and they WILL fly. (If you're not getting it-- this handy tool helps prevent flying parts from going AWOL into your eyeball or under the shop bench!)

The ONLY Pivot Pin Tool you should buy (22.03.2011)

I have a different make pivot pin detent tool and it does work, but not always on the 1st try. This one works like a charm on the 1st try each and every time. Yet another tool, that you can't live without if you build an AR. Buy one and never look back!

Must Have Tool For AR-15 Builders!!!! (07.11.2011)

I ordered this Pivot Pin Dentent Installation Tool specifically for review for my fellow AR-15 builders and enthusiasts. I used this tool yesterday to install two sets of pivot pins on two of my personal AR-15's and I can say this.....What an idiot I was to not have already owned one! This tool works perfectly and everytime!

Anyone who has ever built and AR-15 will tell you that installing the front pivot pin without this tool is a pain in the neck. I have personally lost several detents and springs trying to use makeshift tools to depress the detent itself. This tool is very simple in design and my hat goes of to Brownells for yet another "MUST HAVE" AR-15 tool!

The tool has a nice smooth finish which helps with inserting and removing it from the pivot pin holes in your lower receiver. It is very well made and it shows.

All you have to do is slide it in, align the holes, drop in the spring and detent, turn the tool (which depresses the detent and spring) and push your pivot pin in as you pull the tool out! That's it! Very simple and save you tons of frustration and prevents loosing small parts! I would recommend everyone interested in building an AR-15!!! Thanks Brownells!!!

Handy Tool (18.02.2012)

I haven't gotten a chance to use the tool as of yet but it looks to be sturdy construction and that it will do the job intended.

Absolute Must! (23.03.2012)

Purchased after losing one detent pin.

Had the next pin installed in less than one minute. Absolutely genius piece of gear. I highly recommend this for anyone putting an AR together.

Try the cheap way (13.04.2012)

Actually I dont have one,But they do work Great.
If you need something now,Most folks have a allen wrench that will fit through the pivot holes in there lower,Im sure you know the rest.

Awesome Tool (25.09.2012)

I read the reviews on this tool and thought I would try it without buying this. Then...something told me to get it anyways. Well I have to say it took about 30 seconds to get the pin in and poof...it was complete. At first I thought there had to be more to it. If you are building your lower, "You Cant Do Without This!"

Buy it!!!

Great tool (04.11.2012)

Greatly reduced the likelihood of me shooting my detent pin and spring across my workshop. Definitely pleased with the purchase.

Absolute must have for AR building (16.03.2013)

This is a must-have for anyone planning on building an AR. I can't even imagine installing a pivot pin without one of these now. This thing turns a frustrating process into an afterthought. I use it on every single build and it's saved me much frustration. If you've ever shot a detent or spring out during pivot pin installation, you know what I'm talking about. It's simple, durable, get's the job done easily, and is affordable. Stop mucking around and buy it. You'll be happy you did.

Must have tool! (02.08.2013)

Simple and very effective

Works like a charm (05.08.2016)

Single purpose tool, only good for one thing - but, like most tools, when you need it, you need it.

Nice to have (28.08.2019)

Nice to have for a little over $10 bucks. Worth it!

Must Have Tool (31.08.2019)

If you are putting together an AR-15 Lower this is a must have tool. Save yourself the aggravation and buy this tool. Otherwise you will most likely send your pivot pin and spring flying across the room multiple times! Or go to Ace Hardware and spend $2-$3 and buy a hinge pin and drill the hole to size and this performs exactly and as easily. Either way you will also need another tool to push the detent spring and pin with through the the hole in the installation tool. NOTE: Recommend also buying the AR-STONER AR-15 Roll Pin and Starter Punch Set 7-Piece Steel ($19). The punch set will aid with front pivit pin, as a slave pin for the trigger group and roll pin holder for bolt catch pin installation (if required). Those two tool sets would be my minimum lower tool kit.

Must Have Tool!!! (21.09.2019)

If your building a Lower receiver this is a MUST Have tool!!!

Lesen Sie 17 weitere Bewertungen bei brownells.com

21.9 21.9 1 EUR

Sale

Artikel-Nr.: 080216011
BROWNELLS PIVOT PIN INSTALLATION TOOL 050806104594 Pivot Pin Installations-Tool

18.6 EUR 41 18,60 € * 21,90 €

Lieferzeit ca. 21-30 Tage.
mehr als 10 Stk. im USA Lager.

Eigenschaften: Hersteller/Modell: AR-15

Auf die Wunschliste setzen

Originalbeschreibung

Pivot Pin Installation Tool

Eigenschaften

Hersteller/Modell: AR-15 Versandgewicht: 0,032kg Höhe: 13mm Breite: 69mm Länge: 147mm

Auto-Übersetzung der Beschreibung

Pivot Pin Installations-Tool

Makes installation of the M16 pivot pin and its detent faster and easier. Prevents loss of detents. Guides detent and spring into place and serves as a slave pin when installing the pivot pin.

SPECS: Blued steel. ¼" (6.3mm) diameter. 2½" (6.3cm) and 1½" (3.8cm) long legs .

Mehr...

TECHNISCHE DATEN: Gebläuter Stahl. "(6,3 mm) Durchmesser. 2" (6,3 cm) und 1 "(3,8 cm) lange Beine.

Mehr...

Kundenbewertungen zu BROWNELLS PIVOT PIN INSTALLATION TOOL

Anzahl der Bewertungen: 17
Von brownells.com: 17
Durchschnittliche Bewertung: 5

Another Must Have (05.11.2009)

You should definately have one. (17.02.2010)

A must have (30.12.2010)

I put together my first lower with a parts kit and the very helpul AR-15 videos on Brownells site. I was lucky to have access to this wonderful tool. It made installing the front pivot pin a snap!

Very, very, VERY handy tool! (12.03.2011)

The ONLY Pivot Pin Tool you should buy (22.03.2011)

Must Have Tool For AR-15 Builders!!!! (07.11.2011)

Handy Tool (18.02.2012)

I haven't gotten a chance to use the tool as of yet but it looks to be sturdy construction and that it will do the job intended.

Absolute Must! (23.03.2012)

Purchased after losing one detent pin.

Had the next pin installed in less than one minute. Absolutely genius piece of gear. I highly recommend this for anyone putting an AR together.

Try the cheap way (13.04.2012)

Actually I dont have one,But they do work Great.
If you need something now,Most folks have a allen wrench that will fit through the pivot holes in there lower,Im sure you know the rest.

Awesome Tool (25.09.2012)

Great tool (04.11.2012)

Greatly reduced the likelihood of me shooting my detent pin and spring across my workshop. Definitely pleased with the purchase.

Absolute must have for AR building (16.03.2013)

Must have tool! (02.08.2013)

Simple and very effective

Works like a charm (05.08.2016)

Single purpose tool, only good for one thing - but, like most tools, when you need it, you need it.

Nice to have (28.08.2019)

Nice to have for a little over $10 bucks. Worth it!

Must Have Tool (31.08.2019)

Must Have Tool!!! (21.09.2019)

If your building a Lower receiver this is a MUST Have tool!!!

Lesen Sie 17 weitere Bewertungen bei brownells.com

Kunden kauften auch
Alternativen

Sale

MAGPUL BEV BLOCK-AR15/M4
AR-15 BEV BLOCK

MAGPUL

Lieferzeit ca. 21-30 Tage.
mehr als 10 Stk. im USA Lager. Lieferzeit ca. 21-30 Tage.
mehr als 10 Stk. im USA Lager.

63,68 € *

Alter Preis 74,90 €

Arbeitsblöcke & Schraubstöcke

0 (0)

Anmeldung

Kennwort vergessen?
Registrieren

Site Map

PRODUKT GRUPPEN

Ordering

Kundenservice

Willkommen bei Brownells, dem führenden Händler für Waffenteile, Werkzeug und Zubehör für Waffen in der Benelux!

Unser Versprechen

Wenn Sie gerne schießen oder mit Waffen arbeiten, ob für Hobby, Beruf oder Sport, sind Sie bei uns richtig! Keine Extrakosten für Zoll und kein Mindestbestellwert!

Seit über 75 Jahren vertrauen Schützen, professionelle Büchsenmacher, Enthusiasten, Militär / Polizei und Waffen-Tüftler den qualitativ hochwertigen Waffenteilen und -zubehör von Brownells.

Sie finden bei uns mehr als 50.000 Produkte, darunter einzigartige Waffenteile, Zubehör, Büchsenmacher-Werkzeuge, Munition und andere Produkte zur Wartung, Instandsetzung und Tuning Ihrer Waffen.