The Sinclair Bullet Comparator inserts are meant to be used with the Sinclair Bullet Comparator and Bump Gage Body. These inserts are stainless steel and machined with a taper and a short straight section to more accurately duplicate the chamber throat. This eliminates the wobble experienced with many comparators which have standard drilled holes. Our design allows you to quickly and accurately measure and compare bullet ogive-to-base as well as loaded round ogive-to-cartridge-base measurements. This measurement gives more consistent results than measuring overall lengths since the meplat (the open tip of the bullet) can very by several thousandths of an inch from bullet to bullet.
Mehr...
Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Mehr...
Kundenbewertungen zu SINCLAIR INTERNATIONAL 22 CALIBER (0.224") COMPARATOR INSERT
Anzahl der Bewertungen: 18
Von brownells.com: 18
Durchschnittliche Bewertung: 3,5
Great little tool(13.12.2013)
I bought this comparator to use with the Sinclair XL Comparator body. It fits like a glove and gives accurate measurements from the ojive of the bullet to the base. Buy two of them and two bodies and you can also measure bearing surface of the bullet. I would definitely buy it again.
Well built, but not accurate(20.01.2015)
I have the Hornady bullet comparator that I normally use. When my shooting partner and I noticed a .010 difference in our Hornady headspace comparator, I ordered the Sinclair bump gauge and the bullet comparator. The Sinclair tool is produced from quality steel and is well constructed.
My issue with the tool is that on Sierra MK and Berger Juggernauts, it slides all the way down almost to the base of the bullet. I can't get repeatable results with this tool, where I can with the Hornady tool which is only made of light aluminum. The Sinclair tool does not seem to be measuring from the ogive, but more from the bullet base. As another user reviewed, when used with Comparator body, it measure 1.1 inches, rather than 1.0 like the Hornady. Because of the inaccuracy and non-repeatable readings on the same bullet, I can't continue using this.
Well built and accurate(18.07.2016)
I reviewed this item back in Jan 2015. However, I had just read that the manufacturer had some quality control issues back then, but these have been corrected, so I decided to give these another try. These new ones are much better than before, and hold the bullet securely at the ogive, or the pressure ring on the base by the boat tail. I ordered 2 to get readings on the bearing surface for different bullets, and I get accurate, repeatable readings every time. I have them in the Sinclair body. Since they are cut with a chambering reamer, the bullet fits securely in the insert. In my Hornady insert, the bullet will "wobble" since the insert is cut straight, and you have to make sure it goes on straight on the caliper. This inserts are made of high quality material, and are a must for competitive long range shooters.
Good Fit(12.06.2020)
Good fit without any wobble. I use these bullets for everything.
OK fit with a little wobble(12.06.2020)
I mostly hunt but I like a 1 hole group at 100 yards with 5 shots. These comparators are good but have a little wobble. Construction will outlast me.
Improved design for comparator inserts.(07.12.2010)
Measuring with a tapered comparator is much easier than with a 90 degree edge at the end of a straight hole. Using this insert with the Hornady LNL OAL tools yielded consistant readings on each test. No need to take multiple readings and find the average. A second reading to verify the first and your done. There is one difference though. Getting a reading is quickly done, but if you apply mild pressure and wait a bit you can watch the number go about .002 lower. It feels like your squeezing the air out from between the bullet and comparator surfaces. A tap on the side of the bullet's base is needed to release it from the insert. Rest assured, the insert left no marks on the bullets I measured. This review covers the 6mm insert used to measure 8 different bullets, 80 to 106 grains, by Berger, Sierra and Lapua.
Nice heavy steel, not aluminum(23.03.2011)
Used with the Sinclair comparator body and a caliper to check OAL (base to ogive or datum point) on the bullet. Easy to use with repeatable results. Get two comparators with inserts and length sort the bearing surface area of bullets to help improve accuracy.
Perhaps Too Much Taper(25.11.2013)
I was using this insert to sort 69 grain Sierra Match King bullets. The ogive on the bullet combined with the taper on the insert makes it hard to get repeatable measurements using a caliper. It's much too easy to cause the bullet to move further down into the insert while taking the measurement. The same thing happens with assembled rounds. For these bullets, the Hornady insert works better.
I have a bullet sorting stand and comparators on order, I hope that is more repeatable.
Also, I use a dial caliper. I can zero out the thousandth's but not the tenths of an inch. It would be nice if the comparator assembled to the insert would measure about 1.01 inches rather than 1.11 inches. It's easier to mentally subtract 1 inch from the measurement than 1.1 inches. If you use a digital caliper, it's not a problem.
Buy Hornady instead(16.01.2014)
Simply does not work. When trying to measure SMK in 52, 69, and 77 gr, the comparator simply slides all the way over the bullet until it reaches the case.
works for me(27.06.2016)
I have three different bullet comparators in 22cal, all three measures the ogive at a different point on the bullet. The Sinclair is the best it repeats, and is made of stainless steel so it will not change in time. If seating the bullets deep it maybe a problem it has the largest hole of the three comparator I have . This comparator works great for me.
Improved design, except for 1 problem.(23.12.2010)
All the details in my rating for the 6mm comparator apply here too, but I've found a problem with the .204. To get optimum groups with my Cooper M21 20 TAC, some of my loads need to be seated very deep. The Sierra 32 gr MK and Hornady 45 gr SP achieve 0.25 MOA or better, when seated 0.100" off the lands. That's right, 1/10" jump! At this depth, this new comparator runs into the mouth of the case before it can come into contact with the bullet, so it's useless. And I'm not seating these bullets past their bearing surfaces. I'd like to see the geometry of this insert changed so that the max diameter of it's tapered hole would be 0.202". Right now I measure it at 0.211". In fact all of these new Sinclair inserts should limit their maximum taper diameters to (at most) the diameter of the bearing surface of bullet they are used for.
you get what u pay for(10.03.2014)
Excellent quality - much better than the competition - made of steel - much better that aluminum. Thanks Sinclair!
Eliminate the WOBBLE(03.10.2019)
Previously used the big hex nut with drilled holes for different calibers. Fought the WOBBLE all the time. This comparator insert is so much easier to use for measuring cartridge base to ogive of the bullet. Very important for accurately setting your cartridge overall length. I am a high country Mule Deer hunter but also enjoy long range target shooting.
No wobble(11.06.2020)
Has no wobble but comes close to bottoming our on the case with 200 grain Nosler ballistic tip. The hole could have been a few thousands smaller. Other than that, superior construction and nice weight.
Don't buy(02.07.2015)
The hole in the comparator is that large the base of a bullet goes below the face of the comparator.
I had to give it a star rating but in reality it doesn't even qualify for the one star.
Advised to return it but International shipping is going to be more than the cost of the 3 comparator inserts.
NOPE!(09.04.2016)
Hole sizing is incorrect on mine as well. And I'm not seeing an online way for tech support. Product is useless.
Size Issue Not Corrected(20.12.2016)
The size issue that others have written has not been corrected. The hole is just too large, period. I am very surprised that this has not been rectified, especially coming from Sinclair. I was issued a return tag and I've asked for a Hornady comparator insert and a credit for the difference. I also ordered a Sinclair 22, a 6mm, and a 30 cal comparator, all of which work satisfactorily.
I use these bullets for African hunting. They are a good fit but on the 270 grain bullet they come to the top of the crimp groove, which is acceptable.
Artikel-Nr.: 749000928 SINCLAIR INTERNATIONAL 22 CALIBER (0.224") COMPARATOR INSERT Herstellerproduktnummer: 090224 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12.1EUR5512,10 €
*19,43 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000917 SINCLAIR INTERNATIONAL 375 CALIBER (0.375") COMPARATOR INSERT Herstellerproduktnummer: 090375 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12.3EUR1112,30 €
*17,65 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000918 SINCLAIR INTERNATIONAL 416 CALIBER (0.416") COMPARATOR INSERT Herstellerproduktnummer: 090416 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Artikel-Nr.: 749000920 SINCLAIR INTERNATIONAL 35 CALIBER (0.358") COMPARATOR INSERT Herstellerproduktnummer: 090358 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Artikel-Nr.: 749000922 SINCLAIR INTERNATIONAL 25 CALIBER (0.257") COMPARATOR INSERT Herstellerproduktnummer: 090257 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Artikel-Nr.: 749000923 SINCLAIR INTERNATIONAL 270 CALIBER (0.277") COMPARATOR INSERT Herstellerproduktnummer: 090277 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12.1EUR4212,10 €
*19,43 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000924 SINCLAIR INTERNATIONAL 17 CALIBER (0.172") COMPARATOR INSERT Herstellerproduktnummer: 090172 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Artikel-Nr.: 749000925 SINCLAIR INTERNATIONAL 7MM (0.284") COMPARATOR INSERT Herstellerproduktnummer: 090284 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12EUR1412,00 €
*19,43 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000927 SINCLAIR INTERNATIONAL 20 CALIBER (0.204") COMPARATOR INSERT Herstellerproduktnummer: 090204 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12EUR1212,00 €
*18,64 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000929 SINCLAIR INTERNATIONAL 6MM (0.243") COMPARATOR INSERT Herstellerproduktnummer: 090243 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12EUR2012,00 €
*19,43 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000930 SINCLAIR INTERNATIONAL 6.5MM (0.264") COMPARATOR INSERT Herstellerproduktnummer: 090264SSSSSSSSSSSE Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12EUR2312,00 €
*19,43 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000931 SINCLAIR INTERNATIONAL 30 CALIBER (0.308") COMPARATOR INSERT Herstellerproduktnummer: 090308 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12EUR4912,00 €
*19,43 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 749000926 SINCLAIR INTERNATIONAL 338 CALIBER (0.338") COMPARATOR INSERT Herstellerproduktnummer: 090338 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
12.1EUR012,10 €
*19,33 €
Vorbestellung erforderlich. Lieferzeit abhängig vom Hersteller (ca. 6-12 Wochen).
Artikel-Nr.: 749000919 SINCLAIR INTERNATIONAL 8MM (0.323") COMPARATOR INSERT Herstellerproduktnummer: 090323 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Artikel-Nr.: 749000921 SINCLAIR INTERNATIONAL 45 CALIBER (0.458") COMPARATOR INSERT Herstellerproduktnummer: 090458 Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
The Sinclair Bullet Comparator inserts are meant to be used with the Sinclair Bullet Comparator and Bump Gage Body. These inserts are stainless steel and machined with a taper and a short straight section to more accurately duplicate the chamber throat. This eliminates the wobble experienced with many comparators which have standard drilled holes. Our design allows you to quickly and accurately measure and compare bullet ogive-to-base as well as loaded round ogive-to-cartridge-base measurements. This measurement gives more consistent results than measuring overall lengths since the meplat (the open tip of the bullet) can very by several thousandths of an inch from bullet to bullet.
Mehr...
Die Sinclair Bullet Comparator-Einsätze sind für die Verwendung mit dem Sinclair Bullet Comparator und dem Bump Gage Body vorgesehen. Diese Einsätze sind aus rostfreiem Stahl und mit einer Verjüngung und einem kurzen geraden Abschnitt bearbeitet, um den Kammerhals genauer zu duplizieren. Dies eliminiert das Wackeln, das bei vielen Komparatoren mit Standardbohrungen auftritt. Unser Design ermöglicht es Ihnen, schnell und genau Messungen von Kugel zu Basis sowie geladene Messungen von Kugel zu Patrone zu Basis zu messen und zu vergleichen. Diese Messung liefert konsistentere Ergebnisse als die Messung der Gesamtlänge, da die Meplat (die offene Spitze des Geschosses) von Geschoss zu Geschoss mehrere Tausendstel Zoll betragen kann.
Mehr...
Kundenbewertungen zu SINCLAIR INTERNATIONAL 22 CALIBER (0.224") COMPARATOR INSERT
Anzahl der Bewertungen: 18
Von brownells.com: 18
Durchschnittliche Bewertung: 3,5
Great little tool(13.12.2013)
I bought this comparator to use with the Sinclair XL Comparator body. It fits like a glove and gives accurate measurements from the ojive of the bullet to the base. Buy two of them and two bodies and you can also measure bearing surface of the bullet. I would definitely buy it again.
Well built, but not accurate(20.01.2015)
I have the Hornady bullet comparator that I normally use. When my shooting partner and I noticed a .010 difference in our Hornady headspace comparator, I ordered the Sinclair bump gauge and the bullet comparator. The Sinclair tool is produced from quality steel and is well constructed.
My issue with the tool is that on Sierra MK and Berger Juggernauts, it slides all the way down almost to the base of the bullet. I can't get repeatable results with this tool, where I can with the Hornady tool which is only made of light aluminum. The Sinclair tool does not seem to be measuring from the ogive, but more from the bullet base. As another user reviewed, when used with Comparator body, it measure 1.1 inches, rather than 1.0 like the Hornady. Because of the inaccuracy and non-repeatable readings on the same bullet, I can't continue using this.
Well built and accurate(18.07.2016)
I reviewed this item back in Jan 2015. However, I had just read that the manufacturer had some quality control issues back then, but these have been corrected, so I decided to give these another try. These new ones are much better than before, and hold the bullet securely at the ogive, or the pressure ring on the base by the boat tail. I ordered 2 to get readings on the bearing surface for different bullets, and I get accurate, repeatable readings every time. I have them in the Sinclair body. Since they are cut with a chambering reamer, the bullet fits securely in the insert. In my Hornady insert, the bullet will "wobble" since the insert is cut straight, and you have to make sure it goes on straight on the caliper. This inserts are made of high quality material, and are a must for competitive long range shooters.
Good Fit(12.06.2020)
Good fit without any wobble. I use these bullets for everything.
OK fit with a little wobble(12.06.2020)
I mostly hunt but I like a 1 hole group at 100 yards with 5 shots. These comparators are good but have a little wobble. Construction will outlast me.
Improved design for comparator inserts.(07.12.2010)
Measuring with a tapered comparator is much easier than with a 90 degree edge at the end of a straight hole. Using this insert with the Hornady LNL OAL tools yielded consistant readings on each test. No need to take multiple readings and find the average. A second reading to verify the first and your done. There is one difference though. Getting a reading is quickly done, but if you apply mild pressure and wait a bit you can watch the number go about .002 lower. It feels like your squeezing the air out from between the bullet and comparator surfaces. A tap on the side of the bullet's base is needed to release it from the insert. Rest assured, the insert left no marks on the bullets I measured. This review covers the 6mm insert used to measure 8 different bullets, 80 to 106 grains, by Berger, Sierra and Lapua.
Nice heavy steel, not aluminum(23.03.2011)
Used with the Sinclair comparator body and a caliper to check OAL (base to ogive or datum point) on the bullet. Easy to use with repeatable results. Get two comparators with inserts and length sort the bearing surface area of bullets to help improve accuracy.
Perhaps Too Much Taper(25.11.2013)
I was using this insert to sort 69 grain Sierra Match King bullets. The ogive on the bullet combined with the taper on the insert makes it hard to get repeatable measurements using a caliper. It's much too easy to cause the bullet to move further down into the insert while taking the measurement. The same thing happens with assembled rounds. For these bullets, the Hornady insert works better.
I have a bullet sorting stand and comparators on order, I hope that is more repeatable.
Also, I use a dial caliper. I can zero out the thousandth's but not the tenths of an inch. It would be nice if the comparator assembled to the insert would measure about 1.01 inches rather than 1.11 inches. It's easier to mentally subtract 1 inch from the measurement than 1.1 inches. If you use a digital caliper, it's not a problem.
Buy Hornady instead(16.01.2014)
Simply does not work. When trying to measure SMK in 52, 69, and 77 gr, the comparator simply slides all the way over the bullet until it reaches the case.
works for me(27.06.2016)
I have three different bullet comparators in 22cal, all three measures the ogive at a different point on the bullet. The Sinclair is the best it repeats, and is made of stainless steel so it will not change in time. If seating the bullets deep it maybe a problem it has the largest hole of the three comparator I have . This comparator works great for me.
Improved design, except for 1 problem.(23.12.2010)
All the details in my rating for the 6mm comparator apply here too, but I've found a problem with the .204. To get optimum groups with my Cooper M21 20 TAC, some of my loads need to be seated very deep. The Sierra 32 gr MK and Hornady 45 gr SP achieve 0.25 MOA or better, when seated 0.100" off the lands. That's right, 1/10" jump! At this depth, this new comparator runs into the mouth of the case before it can come into contact with the bullet, so it's useless. And I'm not seating these bullets past their bearing surfaces. I'd like to see the geometry of this insert changed so that the max diameter of it's tapered hole would be 0.202". Right now I measure it at 0.211". In fact all of these new Sinclair inserts should limit their maximum taper diameters to (at most) the diameter of the bearing surface of bullet they are used for.
you get what u pay for(10.03.2014)
Excellent quality - much better than the competition - made of steel - much better that aluminum. Thanks Sinclair!
Eliminate the WOBBLE(03.10.2019)
Previously used the big hex nut with drilled holes for different calibers. Fought the WOBBLE all the time. This comparator insert is so much easier to use for measuring cartridge base to ogive of the bullet. Very important for accurately setting your cartridge overall length. I am a high country Mule Deer hunter but also enjoy long range target shooting.
No wobble(11.06.2020)
Has no wobble but comes close to bottoming our on the case with 200 grain Nosler ballistic tip. The hole could have been a few thousands smaller. Other than that, superior construction and nice weight.
Don't buy(02.07.2015)
The hole in the comparator is that large the base of a bullet goes below the face of the comparator.
I had to give it a star rating but in reality it doesn't even qualify for the one star.
Advised to return it but International shipping is going to be more than the cost of the 3 comparator inserts.
NOPE!(09.04.2016)
Hole sizing is incorrect on mine as well. And I'm not seeing an online way for tech support. Product is useless.
Size Issue Not Corrected(20.12.2016)
The size issue that others have written has not been corrected. The hole is just too large, period. I am very surprised that this has not been rectified, especially coming from Sinclair. I was issued a return tag and I've asked for a Hornady comparator insert and a credit for the difference. I also ordered a Sinclair 22, a 6mm, and a 30 cal comparator, all of which work satisfactorily.
I use these bullets for African hunting. They are a good fit but on the 270 grain bullet they come to the top of the crimp groove, which is acceptable.