There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
Mehr...
Trägt nie Out-Use immer und immer wieder
Es gibt verschiedene Produkte auf dem Markt, mit denen ein Abguss einer Waffenkammer hergestellt werden kann. Um sicher zu gehen, dass das von uns angebotene Produkt das beste und praktischste ist, haben wir den Basishersteller kontaktiert. Sie empfahlen Cerrosafe wegen seiner einzigartigen Eigenschaften. Im Gegensatz zu Woodsmetal, das beim Abkühlen aufquillt und nicht aus einer Pistolenkammer entfernt werden kann, schrumpft Cerrosafe während der ersten 30 Minuten des Abkühlens und hat dann nach einer Stunde GENAU die Kammergröße. Nach 200 Stunden hat es sich um ca. 0,0025" erweitert. Dieser Faktor ist allen Werkzeugmachern bekannt und sie werden ihn bei der Herstellung von Matrizen oder Reibahlen oder Lehren aus Ihrem Guss berücksichtigen - wenn Sie ihnen sagen, dass der Guss von ist Cerrosafe. Cerrosafe schmilzt zwischen 158 - 190 ° F. Es sollte in einer sauberen Eisenpfanne geschmolzen werden. Die Wärmequelle sollte entfernt werden, sobald die Legierung vollständig geschmolzen ist und zu diesem Zeitpunkt gießbereit ist. Das erstarrte Gussstück sollte vor oder während des Abkühlens auf Raumtemperatur aus dem Patronenlager entfernt werden. Wenn es über eine Stunde in der Form verbleibt, greift es an den Kammerwänden und ist schwer zu entfernen. Reinigen Sie das Patronenlager des Gewehrs gründlich, dann verstopfen Sie die Bohrung unmittelbar vor der Kehle mit einem kleinen Lappen - aber nicht so fest, dass sie nicht ausgetrieben werden kann. Wenn möglich, das geschmolzene Cerrosafe durch ein kleines Röhrchen in den Boden des Abgusses gießen und das Röhrchen nach und nach entfernen, während sich die Kammer füllt das Fass ist kalt, erwärmen Sie es auf Zimmertemperatur oder höher, bevor Sie den Abguss herstellen. Nach dem Abkühlen mit einer Stange oder einem Dübel vom Mündungsende der Waffe aus der Kammer entfernen.
Angaben: Verkauft nach Gewicht. Legierung. Endlos wiederverwendbar.
Mehr...
Kundenbewertungen zu BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1/2LB
Anzahl der Bewertungen: 8
Von brownells.com: 8
Durchschnittliche Bewertung: 3,9
great stuff(21.06.2010)
i use this product on chambers and really wroks good to find screw thread pitch when you don't have orginal screw.just fill screw hole then turn the cast out, makes easy to measure.
I must have(07.09.2019)
I used it to cast my Norinco Type 56's chamber to determine the bore diameter. A great product with no mess and easy to use. Also the bore's diameter is now know up a 100th of a millimeter. A must have for the bullet caster.
Safe and Easy to Use(20.04.2020)
Remove the stock and any gun parts that would obscure the chamber or cause the Cerrosafe to be stuck in place when it cools. Lightly oil the chamber and plug the barrel directly below it with wadding to keep the melted Cerrosafe out of the rifling. Clamp the barrel in a padded vice making sure the barrel is plumb (perpendicular to the floor). Heat the gun barrel slightly to allow an even flow of the Cerrosafe into the camber. Break the Cerrosafe into small pieces and melt them in a Lyman Lead Dipper or similar device using a propane torch. Make sure to keep the pour spout slightly above horizontal until ready to pour the melted Cerrosafe into the chamber. Fill the camber with it, but try not to let it overflow. Let it cool for a brief period, and it will shrink slightly. Insert a wooden dowel or cleaning rod in the muzzle and push out the wadding and casting of the chamber. Measure the casting with a dial caliper to determine the chamber dimensions. Compare the casting to an actual cartridge thought to match the firearm in question, If a actual cartridge is not available or doubt remains about the comparison, refer to the SAAMI webpage (https://saami.org/technical-information/ansi-saami-standards/) to match the chamber dimensions with the appropriate cartridge and chamber drawings. The Cerrosafe package includes good instructions. I just put them in my own words.
Cerrosafe- One of a kind(25.10.2009)
Cerrosafe is VERY easy to use. I found it invaluable when I worked at Browning Arms as Chief Firearms Technician. It never wears out and you can use it over and over. It had no faults.
Works as advertised(09.05.2011)
Following directions is a must with this. If you get is stuck, put the gun in an oven at 200 degrees. Stuff comes right out.
Be careful(21.09.2018)
Follow the directions exactly, waited half an hour then proceeded to destroy a cleaning rod trying to remove it from the chamber. I'll have to heat it with a heat gun to remove it from the chamber and buy a new Dewey rod. Not sure exactly what went wrong. I'm hesitant to try it again.
Inspection of the bore of rifle is a mus(04.01.2020)
This product will work if you have a good barrel without in perfections. It will give favorable measurements of a an 1/2 to 1 inch, provided donât have a barrel issues ,like I did . As a diy person. You need to have a gun smith inspect the entire length of barrel with bore scope. For
If the barrel is badly rust pitted the casting will not come out once itâs cooled down solid.
If you try a cleaning rod in a pitted barrel it will bend or break, doesnât have the strength to shear the cast from the rust pit.
Or if you are not aware of a damage in the barrel ,and pour a casting in that exact area like I did the cast will not release. Best to heat the barrel with heat gun and melt it out. Donât use anythlike wooden dowel will break ,or a steel rod like i did. , use a slightly smaller brass or aluminum rod to remove, very carefully, if not donât do it ,melt it out. Thatâs what experience was , donât want you to have to go though, what a diyer like me had to .
After your done have the barrel inspect for casting flash ,you got to get that out of there .
That my experience best have a gunsmith do that has tools for this.
The use of it is straight forward and easy just make sure you knock it out of the chamber or bore at the half hour mark or youâll have to heat it back up to make it flow and redo the job. The 1/2 lb was plenty to cast a chamber with plenty left over and you can reuse it!
Artikel-Nr.: 080027050 BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1/2LB Es gibt verschiedene Produkte auf dem Markt, mit denen ein Abguss einer Waffenkammer hergestellt werden kann. Um sicher zu gehen, dass das von uns angebotene Produkt das beste und praktischste ist, haben wir den Basishersteller kontaktiert. Sie empfahlen Cerrosafe wegen seiner einzigartigen Eigenschaften. Im Gegensatz zu Woodsmetal, das beim Abkühlen aufquillt und nicht aus einer Pistolenkammer entfernt werden kann, schrumpft Cerrosafe während der ersten 30 Minuten des Abkühlens und hat dann nach einer Stunde GENAU die Kammergröße. Nach 200 Stunden hat es sich um ca. 0,0025" erweitert. Dieser Faktor ist allen Werkzeugmachern bekannt und sie werden ihn bei der Herstellung von Matrizen oder Reibahlen oder Lehren aus Ihrem Guss berücksichtigen - wenn Sie ihnen sagen, dass der Guss von ist Cerrosafe. Cerrosafe schmilzt zwischen 158 - 190 ° F. Es sollte in einer sauberen Eisenpfanne geschmolzen werden. Die Wärmequelle sollte entfernt werden, sobald die Legierung vollständig geschmolzen ist und zu diesem Zeitpunkt gießbereit ist. Das erstarrte Gussstück sollte vor oder während des Abkühlens auf Raumtemperatur aus dem Patronenlager entfernt werden. Wenn es über eine Stunde in der Form verbleibt, greift es an den Kammerwänden und ist schwer zu entfernen. Reinigen Sie das Patronenlager des Gewehrs gründlich, dann verstopfen Sie die Bohrung unmittelbar vor der Kehle mit einem kleinen Lappen - aber nicht so fest, dass sie nicht ausgetrieben werden kann. Wenn möglich, das geschmolzene Cerrosafe durch ein kleines Röhrchen in den Boden des Abgusses gießen und das Röhrchen nach und nach entfernen, während sich die Kammer füllt das Fass ist kalt, erwärmen Sie es auf Zimmertemperatur oder höher, bevor Sie den Abguss herstellen. Nach dem Abkühlen mit einer Stange oder einem Dübel vom Mündungsende der Waffe aus der Kammer entfernen.
26.9EUR8926,90 €
*
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
Artikel-Nr.: 080027100 BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1LB Es gibt verschiedene Produkte auf dem Markt, mit denen ein Abguss einer Waffenkammer hergestellt werden kann. Um sicher zu gehen, dass das von uns angebotene Produkt das beste und praktischste ist, haben wir den Basishersteller kontaktiert. Sie empfahlen Cerrosafe wegen seiner einzigartigen Eigenschaften. Im Gegensatz zu Woodsmetal, das beim Abkühlen aufquillt und nicht aus einer Pistolenkammer entfernt werden kann, schrumpft Cerrosafe während der ersten 30 Minuten des Abkühlens und hat dann nach einer Stunde GENAU die Kammergröße. Nach 200 Stunden hat es sich um ca. 0,0025" erweitert. Dieser Faktor ist allen Werkzeugmachern bekannt und sie werden ihn bei der Herstellung von Matrizen oder Reibahlen oder Lehren aus Ihrem Guss berücksichtigen - wenn Sie ihnen sagen, dass der Guss von ist Cerrosafe. Cerrosafe schmilzt zwischen 158 - 190 ° F. Es sollte in einer sauberen Eisenpfanne geschmolzen werden. Die Wärmequelle sollte entfernt werden, sobald die Legierung vollständig geschmolzen ist und zu diesem Zeitpunkt gießbereit ist. Das erstarrte Gussstück sollte vor oder während des Abkühlens auf Raumtemperatur aus dem Patronenlager entfernt werden. Wenn es über eine Stunde in der Form verbleibt, greift es an den Kammerwänden und ist schwer zu entfernen. Reinigen Sie das Patronenlager des Gewehrs gründlich, dann verstopfen Sie die Bohrung unmittelbar vor der Kehle mit einem kleinen Lappen - aber nicht so fest, dass sie nicht ausgetrieben werden kann. Wenn möglich, das geschmolzene Cerrosafe durch ein kleines Röhrchen in den Boden des Abgusses gießen und das Röhrchen nach und nach entfernen, während sich die Kammer füllt das Fass ist kalt, erwärmen Sie es auf Zimmertemperatur oder höher, bevor Sie den Abguss herstellen. Nach dem Abkühlen mit einer Stange oder einem Dübel vom Mündungsende der Waffe aus der Kammer entfernen.
45.9EUR3945,90 €
*
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
Mehr...
Trägt nie Out-Use immer und immer wieder
Es gibt verschiedene Produkte auf dem Markt, mit denen ein Abguss einer Waffenkammer hergestellt werden kann. Um sicher zu gehen, dass das von uns angebotene Produkt das beste und praktischste ist, haben wir den Basishersteller kontaktiert. Sie empfahlen Cerrosafe wegen seiner einzigartigen Eigenschaften. Im Gegensatz zu Woodsmetal, das beim Abkühlen aufquillt und nicht aus einer Pistolenkammer entfernt werden kann, schrumpft Cerrosafe während der ersten 30 Minuten des Abkühlens und hat dann nach einer Stunde GENAU die Kammergröße. Nach 200 Stunden hat es sich um ca. 0,0025" erweitert. Dieser Faktor ist allen Werkzeugmachern bekannt und sie werden ihn bei der Herstellung von Matrizen oder Reibahlen oder Lehren aus Ihrem Guss berücksichtigen - wenn Sie ihnen sagen, dass der Guss von ist Cerrosafe. Cerrosafe schmilzt zwischen 158 - 190 ° F. Es sollte in einer sauberen Eisenpfanne geschmolzen werden. Die Wärmequelle sollte entfernt werden, sobald die Legierung vollständig geschmolzen ist und zu diesem Zeitpunkt gießbereit ist. Das erstarrte Gussstück sollte vor oder während des Abkühlens auf Raumtemperatur aus dem Patronenlager entfernt werden. Wenn es über eine Stunde in der Form verbleibt, greift es an den Kammerwänden und ist schwer zu entfernen. Reinigen Sie das Patronenlager des Gewehrs gründlich, dann verstopfen Sie die Bohrung unmittelbar vor der Kehle mit einem kleinen Lappen - aber nicht so fest, dass sie nicht ausgetrieben werden kann. Wenn möglich, das geschmolzene Cerrosafe durch ein kleines Röhrchen in den Boden des Abgusses gießen und das Röhrchen nach und nach entfernen, während sich die Kammer füllt das Fass ist kalt, erwärmen Sie es auf Zimmertemperatur oder höher, bevor Sie den Abguss herstellen. Nach dem Abkühlen mit einer Stange oder einem Dübel vom Mündungsende der Waffe aus der Kammer entfernen.
Angaben: Verkauft nach Gewicht. Legierung. Endlos wiederverwendbar.
Mehr...
Kundenbewertungen zu BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1/2LB
Anzahl der Bewertungen: 8
Von brownells.com: 8
Durchschnittliche Bewertung: 3,9
great stuff(21.06.2010)
i use this product on chambers and really wroks good to find screw thread pitch when you don't have orginal screw.just fill screw hole then turn the cast out, makes easy to measure.
I must have(07.09.2019)
I used it to cast my Norinco Type 56's chamber to determine the bore diameter. A great product with no mess and easy to use. Also the bore's diameter is now know up a 100th of a millimeter. A must have for the bullet caster.
Safe and Easy to Use(20.04.2020)
Remove the stock and any gun parts that would obscure the chamber or cause the Cerrosafe to be stuck in place when it cools. Lightly oil the chamber and plug the barrel directly below it with wadding to keep the melted Cerrosafe out of the rifling. Clamp the barrel in a padded vice making sure the barrel is plumb (perpendicular to the floor). Heat the gun barrel slightly to allow an even flow of the Cerrosafe into the camber. Break the Cerrosafe into small pieces and melt them in a Lyman Lead Dipper or similar device using a propane torch. Make sure to keep the pour spout slightly above horizontal until ready to pour the melted Cerrosafe into the chamber. Fill the camber with it, but try not to let it overflow. Let it cool for a brief period, and it will shrink slightly. Insert a wooden dowel or cleaning rod in the muzzle and push out the wadding and casting of the chamber. Measure the casting with a dial caliper to determine the chamber dimensions. Compare the casting to an actual cartridge thought to match the firearm in question, If a actual cartridge is not available or doubt remains about the comparison, refer to the SAAMI webpage (https://saami.org/technical-information/ansi-saami-standards/) to match the chamber dimensions with the appropriate cartridge and chamber drawings. The Cerrosafe package includes good instructions. I just put them in my own words.
Cerrosafe- One of a kind(25.10.2009)
Cerrosafe is VERY easy to use. I found it invaluable when I worked at Browning Arms as Chief Firearms Technician. It never wears out and you can use it over and over. It had no faults.
Works as advertised(09.05.2011)
Following directions is a must with this. If you get is stuck, put the gun in an oven at 200 degrees. Stuff comes right out.
Be careful(21.09.2018)
Follow the directions exactly, waited half an hour then proceeded to destroy a cleaning rod trying to remove it from the chamber. I'll have to heat it with a heat gun to remove it from the chamber and buy a new Dewey rod. Not sure exactly what went wrong. I'm hesitant to try it again.
Inspection of the bore of rifle is a mus(04.01.2020)
This product will work if you have a good barrel without in perfections. It will give favorable measurements of a an 1/2 to 1 inch, provided donât have a barrel issues ,like I did . As a diy person. You need to have a gun smith inspect the entire length of barrel with bore scope. For
If the barrel is badly rust pitted the casting will not come out once itâs cooled down solid.
If you try a cleaning rod in a pitted barrel it will bend or break, doesnât have the strength to shear the cast from the rust pit.
Or if you are not aware of a damage in the barrel ,and pour a casting in that exact area like I did the cast will not release. Best to heat the barrel with heat gun and melt it out. Donât use anythlike wooden dowel will break ,or a steel rod like i did. , use a slightly smaller brass or aluminum rod to remove, very carefully, if not donât do it ,melt it out. Thatâs what experience was , donât want you to have to go though, what a diyer like me had to .
After your done have the barrel inspect for casting flash ,you got to get that out of there .
That my experience best have a gunsmith do that has tools for this.
The use of it is straight forward and easy just make sure you knock it out of the chamber or bore at the half hour mark or youâll have to heat it back up to make it flow and redo the job. The 1/2 lb was plenty to cast a chamber with plenty left over and you can reuse it!