The Lee Universal Decapping die is made of steel and designed to allow shooters to decap cases without the need of lube or cleaning. Guaranteed by Lee as unbreakable. Easily removes crimped-in primers. Fits cases up to .550”, not recommended for use on .17-.20 calibers.
Mehr...
Die Lee Universal Decapping-Matrize ist aus Stahl gefertigt und so konstruiert, dass Schützen ihre Hüllen ohne Schmierung oder Reinigung entkappen können. Garantiert von Lee als unzerbrechlich. Entfernt leicht eingecrimpte Grundierungen. Geeignet für Gehäuse bis zu 0,55 Zoll, nicht für die Verwendung mit Kalibern von 0,17 bis 0,20 Zoll empfohlen.
Mehr...
Kundenbewertungen zu LEE PRECISION LEE UNIVERSAL DECAP PIN
Anzahl der Bewertungen: 12
Von brownells.com: 12
Durchschnittliche Bewertung: 4,8
A MUST have with Lee Universal Die(05.09.2019)
If you use a Lee Universal Decaping die, you must have a spare just in case there was a rusted in primer, an old 22 case, or rock inside the care you are de-priming. With a spare rod your progress isn't shut down.
You want a spare!(22.04.2020)
Even though Lee guarantees these as unbreakable, they to break. So have a couple on hand to keep you moving forward in your loading session. Buying from Brownell's cost less than Lee direct.
Works Well for most Calibers(17.02.2011)
The diameter of the decapping rod, which holds the decapping pin, is 0.202". Just small enough to enter a 20 caliber case mouth. Feed it slowly into a 20 caliber case though, because the end of the rod is not tapered enough to avoid possible contact with the case mouth. The diameter of the decapping pin is 0.062" and it is permanently attached to the rod. I'd like to see Lee also make a decapping rod with a 0.059" diameter pin for smaller flash holes like the 6mm BR. Also, if the pin breaks you have to throw away the rod too.
A must have(14.04.2012)
It makes so much sense to remove the primer before tumbling so the tumbling media can clean the primer pocket (if you use ground walnut). The previous reviewer ignored the fact that the die is not intended for calibers that are smaller than .22. Buy it and de-prime before you tumble. The price is great and replacement pins are cheap and easy to find.
Works Okay(04.05.2012)
Yep, it's a decapper. Not much more you can say about it...
Cheap & Works(29.06.2014)
I use this to de-prime all of my brass at a high volume and fast rate for: .223, .270. 300 Blackout, .30-06, etc. I have used this thing a lot and have not broken it yet; even on crimped military brass. I ultrasonic clean my brass after de-priming and have not touched a primer pocket cleaner in years.
Great work Lee!(08.01.2017)
This is the first die I reach for when its time to prep a new batch of rounds. Well machined and great design its incredibly simple. The decapping pin uses a collet, which by design will slip and not snap off if the primer does not wish to budge. Unlike most combination resizing/decapping dies that use a threaded pin that will snap when faced with a stubborn primer. Personally my case prep goes as fallows. De-cap, uniform the primer pocket, remove crimp, de-bur the flash hole. Then on the tumbler. I do it this way so my re-sizing dies never see a dirty case and therefore extending the life of my resizing dies. Great work Lee. Five stars!
Great Value(17.04.2018)
The Lee decapping die is well made, solid and has a nice polished metal finish. The purchase included the decapping pin. It has worked well de-priming crimped and uncrimped cases. It needs about 11 ft-lbs of torque to hold the decapping pin for crimped .223 Rem cases.
Worked as required(05.09.2019)
A very necessary item to de-prime before cleaning cases. No need to lube as the die only removes the primer.
Lee decapping die(21.11.2019)
Pretty simple product. Works good.
A must have work horse! (18.01.2020)
This decapping die by Lee is truly a beast of a work horse. For the price it canât be beat! It takes abuse from crimped in primers and keeps on ticking. And if the pin does finally break or wear out replacements are cheap enough. Just by a few extra pins to keep on hand when you buy the die.
You do have to get a couple of crescent wrenchâs or box wrenchâs to tighten down the collet. And you do have to put some torque on it or the pin will slide out on tough primers, just FYI. But the collet based system saves your pins, BELIEVE ME! I was decapping 357 sig range brass of various brands and found out that Speer has the small flash holes the hard way. But the pin didnât break it just slid up through the collet and actually ended up getting stuck in the flash hole. Had to pull it apart and use pliers to pull it out. Put the pin right back in my die and proceeded to decap the remaining 100 or so cases without issue( AVOIDING THE SPEER BRASS, lol!) so great part by Lee and VERY DURABLE. Lee products donât get the respect they deserve from some folks. Theyâre hard to beat price wise, they work great, they have great customer service, and theyâre made right here in the good ol UNITED STATES OF AMERICA.
Protect your more expensive dies(20.04.2020)
I like to use a universal decapper in my reloading process to help keep my sizing dies clean and prevent fouling from scratching my more expensive sizing dies.
Itâs pretty difficult to mess up a decapping die, but the Lee die does the job well, for a low cost. The slip-collet prevents pin breakage if the die is properly set. For my use, I chucked the spindle in a drill and put a slight bevel on the shoulder of the shank, and filed the pin down to fit through smaller Lapua flash holes - 15 min with a cordless drill, a file, and a couple scraps of sandpaper. The bevel on the shank helps guide the pin into 22 and 20 cal case mouths, and the smaller pin diameter allows decapping of smaller flash hole brass. Iâve decapped tens of thousands of rounds with a Lee Universal decapping did without breaking or bending a pin.
Artikel-Nr.: 100053256 LEE PRECISION LEE UNIVERSAL DECAP PIN Herstellerproduktnummer: 90783734307907839 Die Lee Universal Decapping-Matrize ist aus Stahl gefertigt und so konstruiert, dass Schützen ihre Hüllen ohne Schmierung oder Reinigung entkappen können. Garantiert von Lee als unzerbrechlich. Entfernt leicht eingecrimpte Grundierungen. Geeignet für Gehäuse bis zu 0,55 Zoll, nicht für die Verwendung mit Kalibern von 0,17 bis 0,20 Zoll empfohlen.
7.9EUR2857,90 €
*8,33 €
Lieferzeit ca. 21-30 Tage. mehr als 10 Stk. im USA Lager.
The Lee Universal Decapping die is made of steel and designed to allow shooters to decap cases without the need of lube or cleaning. Guaranteed by Lee as unbreakable. Easily removes crimped-in primers. Fits cases up to .550”, not recommended for use on .17-.20 calibers.
Mehr...
Die Lee Universal Decapping-Matrize ist aus Stahl gefertigt und so konstruiert, dass Schützen ihre Hüllen ohne Schmierung oder Reinigung entkappen können. Garantiert von Lee als unzerbrechlich. Entfernt leicht eingecrimpte Grundierungen. Geeignet für Gehäuse bis zu 0,55 Zoll, nicht für die Verwendung mit Kalibern von 0,17 bis 0,20 Zoll empfohlen.
Mehr...
Kundenbewertungen zu LEE PRECISION LEE UNIVERSAL DECAP PIN
Anzahl der Bewertungen: 12
Von brownells.com: 12
Durchschnittliche Bewertung: 4,8
A MUST have with Lee Universal Die(05.09.2019)
If you use a Lee Universal Decaping die, you must have a spare just in case there was a rusted in primer, an old 22 case, or rock inside the care you are de-priming. With a spare rod your progress isn't shut down.
You want a spare!(22.04.2020)
Even though Lee guarantees these as unbreakable, they to break. So have a couple on hand to keep you moving forward in your loading session. Buying from Brownell's cost less than Lee direct.
Works Well for most Calibers(17.02.2011)
The diameter of the decapping rod, which holds the decapping pin, is 0.202". Just small enough to enter a 20 caliber case mouth. Feed it slowly into a 20 caliber case though, because the end of the rod is not tapered enough to avoid possible contact with the case mouth. The diameter of the decapping pin is 0.062" and it is permanently attached to the rod. I'd like to see Lee also make a decapping rod with a 0.059" diameter pin for smaller flash holes like the 6mm BR. Also, if the pin breaks you have to throw away the rod too.
A must have(14.04.2012)
It makes so much sense to remove the primer before tumbling so the tumbling media can clean the primer pocket (if you use ground walnut). The previous reviewer ignored the fact that the die is not intended for calibers that are smaller than .22. Buy it and de-prime before you tumble. The price is great and replacement pins are cheap and easy to find.
Works Okay(04.05.2012)
Yep, it's a decapper. Not much more you can say about it...
Cheap & Works(29.06.2014)
I use this to de-prime all of my brass at a high volume and fast rate for: .223, .270. 300 Blackout, .30-06, etc. I have used this thing a lot and have not broken it yet; even on crimped military brass. I ultrasonic clean my brass after de-priming and have not touched a primer pocket cleaner in years.
Great work Lee!(08.01.2017)
This is the first die I reach for when its time to prep a new batch of rounds. Well machined and great design its incredibly simple. The decapping pin uses a collet, which by design will slip and not snap off if the primer does not wish to budge. Unlike most combination resizing/decapping dies that use a threaded pin that will snap when faced with a stubborn primer. Personally my case prep goes as fallows. De-cap, uniform the primer pocket, remove crimp, de-bur the flash hole. Then on the tumbler. I do it this way so my re-sizing dies never see a dirty case and therefore extending the life of my resizing dies. Great work Lee. Five stars!
Great Value(17.04.2018)
The Lee decapping die is well made, solid and has a nice polished metal finish. The purchase included the decapping pin. It has worked well de-priming crimped and uncrimped cases. It needs about 11 ft-lbs of torque to hold the decapping pin for crimped .223 Rem cases.
Worked as required(05.09.2019)
A very necessary item to de-prime before cleaning cases. No need to lube as the die only removes the primer.
Lee decapping die(21.11.2019)
Pretty simple product. Works good.
A must have work horse! (18.01.2020)
This decapping die by Lee is truly a beast of a work horse. For the price it canât be beat! It takes abuse from crimped in primers and keeps on ticking. And if the pin does finally break or wear out replacements are cheap enough. Just by a few extra pins to keep on hand when you buy the die.
You do have to get a couple of crescent wrenchâs or box wrenchâs to tighten down the collet. And you do have to put some torque on it or the pin will slide out on tough primers, just FYI. But the collet based system saves your pins, BELIEVE ME! I was decapping 357 sig range brass of various brands and found out that Speer has the small flash holes the hard way. But the pin didnât break it just slid up through the collet and actually ended up getting stuck in the flash hole. Had to pull it apart and use pliers to pull it out. Put the pin right back in my die and proceeded to decap the remaining 100 or so cases without issue( AVOIDING THE SPEER BRASS, lol!) so great part by Lee and VERY DURABLE. Lee products donât get the respect they deserve from some folks. Theyâre hard to beat price wise, they work great, they have great customer service, and theyâre made right here in the good ol UNITED STATES OF AMERICA.
Protect your more expensive dies(20.04.2020)
I like to use a universal decapper in my reloading process to help keep my sizing dies clean and prevent fouling from scratching my more expensive sizing dies.
Itâs pretty difficult to mess up a decapping die, but the Lee die does the job well, for a low cost. The slip-collet prevents pin breakage if the die is properly set. For my use, I chucked the spindle in a drill and put a slight bevel on the shoulder of the shank, and filed the pin down to fit through smaller Lapua flash holes - 15 min with a cordless drill, a file, and a couple scraps of sandpaper. The bevel on the shank helps guide the pin into 22 and 20 cal case mouths, and the smaller pin diameter allows decapping of smaller flash hole brass. Iâve decapped tens of thousands of rounds with a Lee Universal decapping did without breaking or bending a pin.